pps è composto da una struttura ripetitiva ad anello di zolfo e benzene, ha un'eccellente resistenza al calore, resistenza chimica e proprietà meccaniche. dopo lunga impregnazione e fusione della fibra di vetro, stampaggio per estrusione polifenilen solfuro pps rinforzato con fibre di vetro particelle, eccellente stabilità dimensionale, spesso utilizzato come materiale metallico alternativo
-
La materia prima PPS ha riempito parti di automobili ad alta tenacità in fibra di vetro lunga lgf al 40% e altri fileWhat is PPS? PPS has a symmetrical rigid backbone and is part of a crystalline polymer consisting of repeated parapplacement of benzene rings and sulfur atoms. PPS are special engineering plastics with high performance, high melting point up to 280℃, which can replace metal. They are located at the top of the polymer property pyramid, as shown in Figure 1. Therefore, based on the excellent performance of PPS resin, make it meet the requirements of harsh engineering plastic projects for materials. Why filling long glass fiber? Long glass fiber reinforced plastic is on the basis of the original pure plastic, adding glass fiber and other additives, so as to improve the scope of use of materials. Advantages: 1. After glass fiber reinforcement, glass fiber is a high temperature resistant material, therefore, the heat resistance temperature of reinforced plastics is much higher than before without glass fiber, especially nylon plastics; 2. After glass fiber reinforcement, due to the addition of glass fiber, limited the mutual movement between polymer chains of plastics, therefore, the shrinkage rate of reinforced plastics decreases a lot, rigidity is greatly improved; 3. After glass fiber reinforcement, the reinforced plastic will not stress crack, at the same time, the anti-impact performance of plastic is improved a lot; 4. After glass fiber reinforcement, glass fiber is a high strength material, which also greatly improves the strength of plastic, such as: tensile strength, compression strength, bending strength, improve a lot; 5. glass fiber reinforced after, due to the addition of glass fiber and other additives, the combustion performance of reinforced plastics decreased a lot, most of the material can not ignite, is a kind of flame retardant material. Datasheets for your reference I vantaggi prestazionali includono i seguenti aspetti: eccellente resistenza al calore, buone proprietà meccaniche, resistenza alla corrosione, autoignifugo fino al livello UL94 V-0. Poiché il PPS ha i vantaggi delle proprietà di cui sopra e rispetto ad altri tecnopolimeri termoplastici ad alte prestazioni e ha le caratteristiche di facile lavorazione, basso costo, diventa un'eccellente matrice di resina per la produzione di materiali compositi. Dettagli Colore Originale o come richiesto Lunghezza Sopra 5~24mm MOQ 25 kg Pacchetto 25 kg a sacco Porto di carico Porto di Xiamen Tempi di consegna 7~15 giorni dopo la spedizione
- Composito di polifenilensolfuro
- compound in fibra di vetro lunga pps
- Plastica di marca LFT-G
- Materiale rinforzato LGF PPS
- PPS per iniezione
- granuli di plastica pps
Tag :
-
LFT-G PPS Polifenilensolfuro composito resina termoplastica a fibra di vetro lunga colore originaleInformazioni PPS La matrice di resina dei compositi termoplastici comprende tecnopolimeri generali e speciali e il PPS è un tipico rappresentante di tecnopolimeri speciali, comunemente noto come "oro plastico". I vantaggi prestazionali includono i seguenti aspetti: eccellente resistenza al calore, buone proprietà meccaniche, resistenza alla corrosione, autoignifugo fino al livello UL94 V-0. Poiché il PPS ha i vantaggi delle proprietà di cui sopra e rispetto ad altri tecnopolimeri termoplastici ad alte prestazioni e ha le caratteristiche di facile lavorazione, basso costo, diventa un'eccellente matrice di resina per la produzione di materiali compositi. Materiale composito PPS Il materiale composito in fibra di vetro corta (SGF) di riempimento PPS presenta i vantaggi di elevata resistenza, elevata resistenza al calore, ritardante di fiamma, facile lavorazione, basso costo ed è stato applicato nel settore automobilistico, elettronico, elettrico, macchinari, strumenti, aviazione, aerospaziale, militare e altri campi. Il materiale composito in fibra di vetro lunga (LGF) con riempimento in PPS presenta i vantaggi di elevata tenacità, bassa deformazione, resistenza alla fatica, buon aspetto del prodotto e così via. Può essere utilizzato nella girante dello scaldabagno, nel guscio della pompa, nel giunto, nella valvola, nella girante e nel guscio della pompa chimica, nella girante e nel guscio dell'acqua di raffreddamento, nelle parti di elettrodomestici e così via. Quali sono le differenze specifiche tra i compositi PPS rinforzati con fibra di vetro corta (SGF) e lunga (LGF)? 1. Analisi delle proprietà meccaniche The reinforcement fiber added in the resin matrix can form a supporting skeleton, and the reinforcement fiber can effectively bear the external load when the composite is subjected to external force. At the same time, energy can be absorbed by fracture, deformation and other ways to improve the mechanical properties of resin. The tensile strength and bending strength of the composites are gradually increased by increasing the amount of glass fiber. The main reason is that when the glass fiber content increases, more glass fiber in the composite material can withstand the action of external force. Meanwhile, due to the increase in the number of glass fibers, the resin matrix between the glass fibers becomes thinner, which is more conducive to the construction of glass fiber reinforced frame. Therefore, with the increase of glass fiber content, more stress is transferred from resin to glass fiber under external load, which effectively improves the tensile and bending properties of composite materials. The tensile and bending properties of PPS/LGF composites are higher than those of PPS/SGF composites. When the glass fiber mass fraction is 30%, the tensile strength of PPS/SGF and PPS/LGF composites is 110MPa and 122MPa, respectively. The bending strength was 175MPa and 208MPa, respectively. The flexural elastic modulus were 8GPa and 9GPa, respectively. The tensile strength, bending strength and bending elastic modulus of PPS/LGF composites are increased by 11.0%, 18.9% and 11.3% compared with PPS/SGF composites, respectively. PPS/LGF composites have higher length retention rate of glass fiber. Under the condition of the same glass fiber content, the composites have stronger load resistance and better mechanical properties. When the glass fiber content is low, the impact strength of the composite decreases. The main reason is that the lower glass fiber content cannot form a good stress transfer network in the composite material, so that the glass fiber exists in the form of defects under the impact load of the composite material, resulting in the overall impact strength of the composite material is reduced. With the increase of the glass fiber content, the glass fiber in the composite can form an effective spatial network, and the reinforcement effect is greater than that of the glass fiber tip. Under the action of external load, the external load can be transferred to the reinforced fiber better, thus improving the overall performance of the composite. In the PPS/LGF system, the length of the glass fiber is longer and the spatial network is more dense. The reinforced glass fiber has greater bearing capacity and better impact strength. When the mass fraction of glass fiber is 30%, the impact strength of PPS/LGF is increased by 19.4% from 31kJ/m2 to 37kJ/m2, and the notch impact strength is increased by 54.5%(from 7.7kJ/m2 to 11.9kJ/m2). 2. Thermal properties analysis of PPS/SGF and PPS/LGF composites When the mass fraction of glass fiber is 30%, the thermal deformation temperature of PPS/SGF composite and PPS/LGF composite reaches 250℃ and 275℃, respectively. The thermal deformation temperature of PPS/LGF composite is 10% higher than that of PPS/SGF composite. The main reason is that the introduction of glass fiber makes the network skeleton of reinforced fiber formed inside the composite material...
- Nuova resina termoplastica ad alte prestazioni
- Un polimero cristallino
- Plastica di riempimento in fibra di vetro lunga
- Materiale personalizzato
- Materia prima industriale
- Elevata resistenza agli urti
Tag :
-
Materia prima PPS fibra di vetro lunga composita per parti di elettrodomesticiCodice prodotto: PPS-NA-LGF Specifica della fibra: 20% -60% Caratteristica: 94-VO Ritardante di fiamma, elevata tenacità, bassa deformazione, resistenza alla fatica, buon aspetto del prodotto Applicazione: girante dello scaldabagno, guscio della pompa, giunto, valvola, girante della pompa chimica, guscio, girante dell'acqua di raffreddamento, guscio, parti di elettrodomestici
- 94-VO Ritardante di fiamma
- Elevata tenacità
- Deformazione bassa
- Girante scaldabagno
- Guscio della pompa
- Campione disponibile
Tag :
-
PPS Composito plastico in fibra di vetro lunga polifenilensolfuro ad alta tenacitàCodice prodotto: PPS-NA-LGF Colore del prodotto: colore naturale Specifica della fibra: 20% -60% Caratteristica del prodotto: 94-VO ritardante di fiamma, alta tenacità, bassa deformazione, resistenza alla fatica, buon aspetto del prodotto. Applicazione del prodotto: girante dello scaldabagno, guscio della pompa, giunto, girante della pompa chimica, girante dell'acqua di raffreddamento, parti degli elettrodomestici.vedere di più
-
Composito PPS LGF 40% termoplastico a fibra lunga LFTnome del prodotto: fibra di vetro lunga 40% riempimento pps lunghezza: circa 12 mm applicazione: componenti per auto, componenti energetici e altre parti in plastica
- PPS LGF
- composito PPS con riempimento in fibra di vetro
- Polimero PPS
- LFT PPS fibra di vetro 40%
- LFT PPS
Tag :
-
LFT PPS LGF30% pellet di polimero PPS con riempimento in fibra di vetronome del prodotto: fibra di vetro lunga 30% di riempimento PPS, polimero LFT PPS lunghezza: circa 12 mm applicazione: componenti per auto, componenti energetici e altre parti in plasticavedere di più
-
LFT PPS LGF20% granuli termoplastici rinforzati per equipaggiamento aeronauticonome del prodotto: PPS in fibra di vetro lunga 20% materiali compositi,ft PPS lunghezza: circa 12 mm , personalizzare 5-25 mmvedere di più
-
LFT PPS granuli compositi termoplastici in fibra di vetro lungaPPS granuli termoplastici rinforzati con fibra di vetro lunga per introduzione e proprietà
- fibra di vetro pps materiale termoplastico
- pps stampaggio di fibre
- pps lgf fibra di vetro
- colore naturale pps lgf composito
- PPS pellet in fibra di vetro polimero
- granuli vergini termoplastici PPS
Tag :
-
PPS fibra lunga LFT migliorare la resistenza pps per profilopolifenilene termoplastico rinforzato con fibra lunga solfuro pps granuli has94-V0 ritardante di fiamma.
- compositi a fibra lunga pps
- pps composto termoplastico
- pps fibra di vetro lunga
- lft pps termoplastico a fibra lunga
- fibra di vetro lunga pps polimero
- termoplastiche rinforzate con fibre lunghe
Tag :
-
pps prezzo resina pps termoplastica rinforzata con fibra di vetro lunga pps granulipolifenilene solfuro pps termoplastico rinforzato con fibre lunghe pps granulivedere di più
-
pps polifenilene polimero termoplastico rinforzato granuli di solfuro lgf gf30polifenilene termoplastico rinforzato con fibra lunga solfuro pps granulivedere di più
-
materiale vergine pps rinforzato con fibra di vetro lunga termoplastico per nuovo separatore di energiapolifrnilene solfuro pps termoplastico rinforzato con fibra di vetro lungavedere di più